← Guide

Roofs and levels

Every building's roof as a level of its own; how a crane's drop zone reaches roofs and unslabbed storeys; the same-contractor exemption; level badges and area chips on the map; the level prompt for workers and plant; and where an area stands vertically.

People work on roofs, and a crane's load passes over them. SimOps gives every building a Roof above its floors, so a roofer can be placed there, shown there and caught by the crane's drop zone there. This page explains where things stand vertically in a building: workers and plant, which you place on a level, and areas, which you draw.

Every building has a roof

A building is a stack of floors (storeys) with its roof on top. The roof is added for you when the building is drawn or imported, and it is always there:

  • It is a level like the floors. It has a label (Roof until you rename it in the building editor), an outline, and it can hold a floor plan. It is the top entry in the building's Floors list, marked open air, and you can focus it like any floor.
  • It cannot be removed or moved. The building editor pins it at the top; adding a floor puts the new floor beneath it.
  • It is not a floor. "3 floors" means three storeys with the roof above them. Wherever SimOps names a level in words it uses the level's label, so a roofer reads Admin building · Roof, never "level 3".
  • It is open air. The ground outside buildings and the roofs together make up the Open-air surface: what you see from above, and what the site map shows.

The roof is the top of the finished building. While the floors are still going up, the highest poured deck is an ordinary floor with nothing above it yet; it is not the roof.

The crane and what it can reach

A crane's drop zone reaches whatever is Exposed beneath it, whichever level the crane itself stands on. Something under a poured slab is protected; everything else is exposed.

  • A worker or area on the roof is always exposed. Nothing is ever poured above a roof.
  • A floor is protected only once the slab above it is poured. Each building records its Slab count: the number of floors with a poured slab above them, counted up from the ground. Set it in the building editor under Slab count: No slabs poured leaves every floor exposed, Slab above Ground Floor poured protects the ground floor, and so on up to Roof slab poured, which protects every floor. Even then, the roof itself stays exposed.
  • An area on a protected floor is protected only where the floor above covers it. If the area reaches out past the wall, the crane still clashes with the part outside.
  • A worker whose floor is not set is treated as exposed. SimOps does not know whether a slab is over them, so it takes the safe reading (see Floor not set below).

Three rules use this test. Worker in Crane Drop Zone (red) fires for an exposed worker inside the drop zone. Crane Drop Zone in Work Area and Crane Drop Zone in Laydown Area (amber) fire when the drop zone meets an exposed part of another firm's area. Crane Drop Zone on Road is unchanged, because roads are at ground level. No crane rule tests exposure for exclusions or points of interest. A crane whose drop zone reaches a high-risk commissioning area on the same level is still caught red by Entity inside high-risk commissioning area, whichever firm owns the crane.

The same-contractor exemption

Worker in Crane Drop Zone does not fire for a worker under their own firm's crane. The rule assumes a firm coordinates its own lifts. That holds on a roof as it does anywhere else, so an M&E roofer under the M&E firm's crane raises no clash. The two crane-and-area rules work the same way: they fire only for another firm's area.

A site that wants the clash between a firm's own crane and its own workers can turn the exemption off in its own rule profile. The rule is changed in Settings → Rules → Clash. While the Active Profile is marked system default, its rules have no Edit: the site first takes its own copy with Clone to Site (then Clone in the form that opens) and turns it on with Activate on the copy under Site Profiles. On the site's active profile, Manage lists the rules; Edit on Worker in Crane Drop Zone opens it, the condition Entities belong to different contractors under Conditions is removed with its ×, and Save Changes keeps the change.

The change is to your site's profile only, and it catches more than roofers. The rule's other party is a crane or a concrete pump, so from then on that firm's own workers raise it wherever they are exposed under its drop zone: at ground level as well as on a roof. Crane Drop Zone in Work Area and Crane Drop Zone in Laydown Area carry their own copy of the condition, so they still fire only for another firm's area unless you remove it from them as well. See Configuring clash rules.

What the map shows

The site map stays flat and names the level in short codes:

  • Level badges. A worker or plant inside a building carries a badge: R on the roof (whatever the roof is called), G on the ground floor, L1, L2 … on the floors above, B1 … below ground. A badge of ? means the worker is inside a building with no floor recorded: Floor unknown, which the properties panel shows as Floor not set. Lists, cards and the properties panel print the level's label instead of the code. A worker on the floor you have focused drops the badge, since the view already says which floor it is.
  • Roof workers are always drawn on the site map, so you can see them beside the crane.
  • Workers on a floor follow your indoor setting. Under Settings → You → Indoor Workers you choose how workers inside buildings show while nothing is focused: Always shows the ground-floor workers of every building, On Hover (the default) shows a building's ground-floor workers while you hover over it, and On Select shows none. Workers on an upper floor appear when you focus that floor. A worker whose floor is not set is always drawn.
  • Area chips. An area placed on a roof carries a ROOF chip. An area on All levels that crosses a building carries ALL LEVELS, and an area on Open air only that crosses a building carries OPEN AIR. An area that crosses no building carries no chip: out in the open the two read the same.
  • Focusing the roof keeps the outdoors in view: the crane, its whole drop zone and the ground beside the building are not dimmed, as they are when a floor is focused.

Placing workers and plant

A worker or plant is always stored on a level: a floor, or the roof. Nothing on site works out that someone is on a roof; it is a place you choose.

  • Dropping one into a building with nothing focused opens the level prompt. It lists only the levels whose outline holds the point you clicked, with the lowest of them selected and the roof marked open air. It opens in every building, a one-floor building included. Press Enter to accept the selection, or pick another level and press the button that names it, such as Place on Roof.
  • With a level of that building focused, a new drop lands on that level without asking; a drop into any other building opens the prompt. When you place a worker from a permit that names a level, the permit's level is used instead.
  • Dragging one into a building always asks, even with a level focused, and the prompt's button reads Move to and the level. Within the same building the prompt selects the worker's own level. In another building, a roof worker is offered that building's roof; a worker on a floor is offered the focused level if that building is focused, otherwise the lowest level. One undo puts the worker back where it was, building and level included.
  • Dragging one out of every building makes it an outdoor worker, with no prompt.
  • A level cannot be cleared. To take a worker out of a building, move it out of the building. If SimOps cannot check which building is under the point, it saves nothing and tells you.
  • The worker and plant forms carry floor buttons for the building, the roof among them, and the edit form is where you change a level later.

An import never guesses the roof: a worker lands on a roof only when the file says so. Where a file does not say which floor and the point is over more than one floor, the floor is left unset for you to fill in.

Floor not set

A worker inside a building with no floor recorded is Floor unknown. SimOps reads it cautiously: it is exposed to a crane overhead, it meets workers on any floor of that building, and it is never taken to be on the roof. Open it and pick the floor in the edit form.

Areas: where an area stands

Drawing an area never asks a question. Where it stands vertically is set in its form, under Vertical position, which lists:

  • Open air only: the area lies on the open-air surface. It meets what is outdoors and, in each building its shape crosses, what is on the roof and any worker there whose floor is not set. It meets nothing on a floor below the roof.
  • All levels: the area lies on every floor and the roof of each building its shape crosses, and on the ground outside. It is drawn on the site map and in every floor view of those buildings. Deleting it removes it from every level, and SimOps says so before you confirm.
  • One row per level of each building the shape crosses, written as Admin building · Roof or Admin building · Level 1: the area lies on that level only.

An area made by Fill stands where its container does. A Whole-floor area has no Vertical position picker: it stays on its Fill's floor (see Moving an area below). A Whole-zone area's picker offers only Open air only and All levels.

Areas drawn with no level are Unplaced, and their Vertical extent is either Open air only or All levels. The type sets the starting position:

  • an exclusion or a high-risk commissioning area starts on All levels, so a keep-out zone drawn across a wall still binds the people inside;
  • a work area or a laydown starts on Open air only.

With a level focused, the form starts on that level when the shape crosses the focused building. You can change the position when you create the area or later; changing an area's type afterwards does not move it.

A recurring area has one position for every day. Changing it changes every occurrence. A single day cannot be moved to another level on its own: SimOps refuses and says why. To have one day somewhere else, delete that day and draw a separate area.

Moving an area. Dragging a placed area as a whole opens the prompt Where does it stand now? whenever it still crosses a building, with its own level selected if it is still in its building, or else the same kind of level in the building it overlaps most, or Not on a level. Enter confirms, and Cancel or Escape puts the area back. An area dragged clear of every building becomes unplaced, with its type's starting position, and SimOps tells you. Editing an area's corners never asks, and an unplaced area never asks when it is moved. A Whole-floor area, made by Floor-fill, never asks either: it stays on its Fill's floor wherever its shape goes, and that floor is changed through the Fill on the building panel, never by a move.

A ground-floor area drawn past its wall

A ground-floor area may reach out through the wall, for example "this floor and the apron by the door". The part outside every building lies on the ground outside: it meets what is outdoors there, such as a worker standing on the apron. Only the ground floor does this. The part of an upper-floor or roof area drawn past the wall meets nothing below it, though a crane still reaches it there.

On the site map with nothing focused, only the part outside is drawn. The part under the roof appears when you focus that floor. A ground-floor area entirely inside its building draws nothing on the site map, and its clashes still appear on the noticeboard. An area drawn exactly to a wall it shares with the next building does not reach through it; one that does reach into a second building is on the same floor there.

A worked example

Take a three-storey building with every slab poured, and a tower crane belonging to the civils firm standing outside its east wall, its drop zone reaching over part of the roof.

  • Two M&E roofers on the roof. The one inside the drop zone clashes red, Worker in Crane Drop Zone: the roof is always exposed, and the crane belongs to another firm. The other roofer, clear of the drop zone, has no clash. Both carry the R badge.
  • An M&E work area placed on the roof, under the drop zone. It carries the ROOF chip and clashes amber, Crane Drop Zone in Work Area. The roofer in the drop zone stands in it without a clash, because it is their own firm's area.
  • An M&E fitter on Level 1, under the same drop zone. The poured slab above Level 1 protects them, so there is no clash. They appear when Level 1 is focused.
  • An exclusion on All levels drawn across the west wall. It carries the ALL LEVELS chip and is drawn on every floor of the building and outside it. Nobody stands in it, so it raises nothing, but a worker entering it on any floor, on the roof or in the yard would clash red.
  • Ground work beside the building. A third firm's ground-floor work area runs out through the north wall. A joiner works inside it on the ground floor (G), and a banksman stands on the apron outside. The site map draws only the apron; focusing the ground floor shows the rest. Neither worker is under the crane, so neither has a clash.

If the crane belonged to the M&E firm, neither the roofer in the drop zone nor the roof work area would raise a clash. A site that wants the roofer caught turns the same-contractor exemption off on Worker in Crane Drop Zone.


See also: The spatial and temporal model · Configuring clash rules · How activity reaches people. Terms: glossary — Roof, Open-air surface, Unplaced, Vertical extent, Floor unknown, Slab count, Exposed.

Was this page useful? Report a problem

No cookies and no third-party analytics. A verdict records this page's path — and a search that finds nothing records the words you typed — in this site's own server log.

Generated from source · SimOops living system reference